IVA Passed!!!

IVA test passed today, very happy indeed.  Decided to trailer the car up there as I didn't fancy 20 miles on the M1 for my first drive on the road.  Got up to Notitngham at about 7.45am so drove past the text centre and away from nottingham for 10 minutes where we found a quiet side street and unloaded the car from the trailer and then headed back to the test centre.  I used the 10 minute drive to bed the brakes in which seemed to be working well.

The test got under way with Martin checking front suspension and radius of everything.  The only issue was the mounting bracket on the silencer I borrowed from MK didn't meet the radius requirements.  He allowed me to file the edges at the end of the test.

He then disappeared around the back of the building for 10 minutes to weight the car and I assume to check mirrors, self centring etc.  The car weighed in at 480kg.

Next was the emissions.  First attempt it failed on hydrocarbons so he allowed me to connect the laptop and tweak the figures.  It was hit and miss as I hadn't got a clue which way to adjust them but on the 2nd attempt after changing a few of the blocks slightly it passed, much to my relief.

Next it was up on the ramp to check under the car - no issues to report here.  Martin was very complimentary on the quality of the build which was nice to hear!

Brakes next.  Again, no issues here.  Everything was well within the limits.

Final job was noise.  I drove outside for this and held the revs at 8000 rpm for a few seconds.  It came in at 94dB so again, well within the limits.

So, 3 hours and £450 later I get a certificate to say its passed the IVA.  Decided to drive the car all the way home which was awesome.  The motorway drive revealed the car has quite a lot of vibration at 60-70mph which I am not sure if it is a problem with the car or if that is just how the MK Indy is cruising at those speeds.  The country roads from the motorway were much more fun as I got the chance to test the acceleration.  This thing is quick and the clutchless shifting at 11krpm is amazing.  So much fun!

Now it's a case of applying for registration with the DVLA which I'm hoping isn't too painful a process.

Upper ball joint covers

Today I spoke to the guys at the test centre about the covers for the upper ball joints and steering rack lock nuts.  They explained it something along the lines of.......

If your car goes to a garage for work to be done, the garage should be able to put the car back to how it was before they started work.  If you have to cut off heatshrink, remove tape etc then it wont go back on when the work is done.  Cable ties are acceptable for securing the covers but if the ties are removed, the covers shouldn't fall off, e.g. splitting some silicone coolant hose and cable tying it on isnt acceptable.

They recommended cable gland shrouds so I went to City Electrical Factors and picked up a pair of 40mm glands and 20mm glands.

I stripped down the front end and removed the top ball joints, taking care to mark the threads so I knew how far to put them back so as not to mess up the geometry.  I cut the 40mm gland shrouds as per the photo below and slid them on the top wishbone before putting the top ball joint back.   The shroud was secured in position with a cable tie.

This now allows the locking nut to be tightened and undone whenever and the shroud wont come off unless the ball joint is removed.

For the steering rack I did the same but with the 20mm shrouds.

Retro-reflectors = reverse motor cover

Not much left to do on the car now so today I installed the rear reflectors.  The type I bought have a hole in the centre so I fixed them below the rear light clusters with an M5 bolt, ensuring they were minimum 250mm form the floor and maximum 400mm from edge of vehicle.

I also removed my reverse motor cover as it got damaged going over a speed bump on my parents drive.  The cover did its job as the motor was not damaged.  For now I will straighten with a hammer and look to make one from steel after the IVA.